Chrysler Check Engine Light

Chrysler Check Engine Light

Chrysler Check Engine Light

The Chrysler check engine light warns the driver that something is wrong with one of your car’s components (in most cases, the emission system).

Even if your Chrysler drives without performance issues, do not ignore the engine light. If there are no engine noises, the engine doesn’t shake, or is not overheating; you can continue to drive with caution. Get the car diagnosed as soon as possible.

If your Chrysler check engine light is on, pay attention to how your car performs. In some cases, you may notice one or more of the following problems:

  • Rough idling
  • Poor acceleration
  • A decrease in MPG/fuel economy.
  • Engine shakes or runs rough
  • Engine overheating

The symptoms can vary depending on which component or sensor is malfunctioning.

How many miles to with the check engine light?

The Chrysler engine light could be triggered by anything from a faulty sensor to wires that might need replacement or tightening. If your car’s check engine light is showing, then you should pull over and get a help from your mechanic if your car can travel for a mile you need to cover or get a tow truck. This is because check engine codes deliver different message according to its severity. And it’s essential to know how far you can travel before its affects your car system entirely.

Cause Of check engine light?

A steady glow is an indication of a minor fault while a flashing check engine light means something very serious with your Chrysler 300 that needs urgent attention. so, when this occur, it’s important to contact Chrysler service to know next line of action.

So, here are reasons why your check engine light might come on.

  • Vacuum leak
  • Loose gas cap
  • MAF sensor
  • Low or dead battery
  • Spark plugs
  • Aftermarket items
  • Catalytic converter
  • Oxygen sensor
  1. Your Chrysler 300 has a vacuum leak. Chrysler 300 comes with a vacuum system that’s integrated with a lot of functions. The vacuum system regulates harmful emissions by directing the fumes as your car’s gasoline burns through the engine. If your car’s RPM is high in idle or randomly surges, then your car has a vacuum leak fault. Over time, vacuum hoses get weak and starts to crack if they’re have been exposed to extreme heat or speeding.
  2. Another most common fault of the check engine light is a loosen gas cap, damaged or missing. The Chrysler 300 gas cap has many purposes. It hinders the gas fume from evaporating when you’re not driving, it covers the fuel system and maintain pressure within the fuel tank.
  3. Your mass airflow sensor (known as MAF) needs to be replaced. If you read on my previous article on how to replace the Mass Airflow Sensor, you can easily do this if it’s the reason for the check light. A faulty Chrysler 300 MAF can trigger this warning because it measures the amount of fuel your car needs to run the engine efficiently. It does this by measuring the air supply needed by your car’s engine. As part of the engine system, it regulates and adjusts changes in your engine like altitude. So, if you noticed your Chrysler 300 has issue starting, idling rough, or your throttle has shifted from usual state, this is a sign faulty MAF.
  4. The battery is low or dead. When your Chrysler 300 battery is low or dead, it triggers this warning. So, if you have a dead battery, you can’t do anything with your car until you replace it or if its low, you can charge it.
  5. New Spark Plugs or Plug Wires are paramount for your Chrysler 300. The spark plugs are there to ignite the air/fuel collection in the combustion chamber of your Chrysler 300. These sparks plugs are what causes the car pistons to move and helps the engine run. The spark plug is in charge of delivering spark from the ignition coil to the spark plugs. If these spark plugs are faulty or dead, you should replace them.
  6. Issues with any aftermarket items. An aftermarket of anything on your car like alarm, exhaust, or substituted item can cause the check engine light to come on if they’re not properly installed. The aftermarket parts of your vehicle can drain the battery and even cause poor electric flow on your car. If you notice something like this in your car, consider taken it to a mechanic for proper adjusting and fixing.
  7. Your catalytic converter is bad or going bad. The catalytic converter is part of the car’s exhaust system. It functions by turning the carbon monoxide produced by the combustion process into carbon dioxide. If your catalytic converter is faulty and you don’t get it fixed sooner. Your vehicle will fail to pass emission test, indicate poor engine performance, and will cause your fuel to drain quicker. It will also cause you fuel economy.
  8. Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, referred as the O2 sensor is there to measure the oxygen received by your exhaust system. If the sensor is bad, your car will burn fuel faster and your car will have fuel economy issue. When you fail to replace a failed O2 sensor, it can affect your car’s fuel economy and also damage your Chrysler 300 catalytic converter and spark plugs.

Check Engine Light Service Chrysler 300

When driving and you notice the check engine light illuminating. If you’re a new car owner, you might be deeply worried on the cause of this. But, ignoring your car’s warning could lead to severe damage to your car’s engine. So, don’t take all warning lightly even if you’re an old car owner.

So, your Chrysler 300’s ECM (electronic control module) identifies any electronic control fault in your car that it can’t correct. The computer onboard system (the ECM) sends the check engine light.

Once the light is triggered, the ECM records the engine code in its memory to help experts identify the cause. This code can be read using an electronic scan tool by auto experts to find the fault with your car.

What Does the Check Engine Light Mean?

The check engine light can be triggered by different errors; therefore, it means variety of things. For educational purpose, the check engine light can mean your gas cap is loose or an indication your engine is about to knock.

Chrysler 300 Check Engine Light

As said earlier, when your check engine light flashes. It means a serious problem with your Chrysler and need urgent attention. Don’t waste time to take your car to mechanic if the light is flashing as it may cause severe damage to your car.

Chrysler 300 Check Engine Light Flashing

Another reason for your Chrysler check engine light to flash might be bad head gasket, malfunctioning of the fuel injection system, dirty mass airflow defective sparks, or even damaged oxygen sensor.

Chrysler 300 Check Engine Light Codes

The term diagnostic trouble codes (DTC), is used to refer to the check engine light codes. These are car computer codes stored by the ECM for the diagnoses of your car.

Reasons for the light, including:

  • Bad Spark Plugs
  • O2 Sensor
  • Fuel and air metering systems problems
  • Computer output circuit defects
  • Old Battery
  • Ignition system faults
  • Emissions controls faults
  • Loose Gas Cap or Missing Gas Cap
  • Transmission issues

Is it safe to drive with the check engine light?

Depends on the light indication on the check engine, if the light illuminates, it might be less issue but still require attention. But when the light flashes, your Chrysler 300 requires urgent mechanic attention.

Will the check engine light reset itself?

The check engine light on your 2014 Chrysler 300 will normally shut itself off if the issue or code that caused it to turn on is fixed. For instance, if the cause of your check engine light coming on was a loose gas cap, if it’s tightened, the light will promptly turn itself off. Likewise, if your catalytic converter is working correctly.

And you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2014 Chrysler 300 light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to take it to a mechanic shop so the light and code can be double-checked and reset.

Cost to get the engine light checked?

The cost to get the check engine light diagnosed and testing can range between $88 and $111.

Final Thoughts

We believe you must have learnt a lot from this article as regards your check engine light and the possible causes. As stated above, don’t take any error indication of your car lightly as it may impact your car’s engine without further notice.

About Daves 41 Articles
David Samuel is an accountant and Tech-Savvy. He is the author of Art of Public Speaking available on Amazon KDP. Blogging is part of his hubby as he likes sharing ideas with his huge fan base on Facebook and Twitter.

3 Trackbacks / Pingbacks

  1. Is Your Brake Lamp Bulb Faulty? - HOW TO LEARN MORE
  2. How To Fix Car And Lock Symbol - HOW TO LEARN MORE
  3. Everything About Acura B12 Service - HOW TO LEARN MORE

Leave a Reply

Your email address will not be published.


*